Vehicles
Sections
68 not categorized PORSCHE 911 TURBO ABS RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 - Transmission (includes uncategorized and accessory items) F97641210TUM021R02 Ohne logo
$806.33
Make a selection 115343615B8 Twintube strut assembly setting: b8 sport (sp) drive type: awd position: front quantity per vehicle: 2 bilstein b8 sport shocks and struts deliver absolute mastery of the road surface for the performance-minded driver. Designed to push a car's suspension to its performance peak, these shocks are specifically suited for use with special lowering springs in combination with anti-sway bars or other suspension upgrades. (yellow paint, steel body)
$485.10
Make a selection 115993S1 Lowers the ride height by 30 mm (1.2 inches) in the front and 30 mm ( 1.2 inches) in the rear.
$663.30
Make a selection F97641210TUM021
$1,186.90
Make a selection 20934TD8SS It was only a matter of time before clutch masters built the ultimate clutch kit for the Porsche 996 and 997 turbo. With the success of their stage 3 OEM replacement kits holding 700 horsepower with daily driveability, clutch masters wanted to step up their clutch game and release this new 8.5 inch twin disk clutch with flywheel for the Porsche 911 turbo. This race version of the twin disk is recommended only for race use as initial pedal engagement as it requires finesse. The complete clutch weighs an astonishing 23lbs. The stock flywheel alone weighs about 40lbs! General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$6,156.00
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 20934HDFF The perfect clutch for aggressive drivers who want that strong 1st and 2nd gear holding power. What most people use to buy as the "stage 3", this is now 1 step up with fiber tough on both sides giving a slightly more aggressive pedal feel and what makes the fx350 perfect for high amounts of torque. The dual sided fiber tough disc does make start and stop a little getting use to, but is an aggressive disk that will hold your high horsepower Porsche 996 tt. 1st gear takes a little bit of pedal control but after that the car engages and drives like oem. Clutch masters fx350 will provide more holding power than stage 1 & 2, yet it still offers exceptionally smooth driveability and long life. Combined with the alu...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09
$2,505.33
Make a selection 20934TD8RS It was only a matter of time before clutch masters built the ultimate clutch kit for the Porsche 996 and 997 turbo. With the success of their stage 3 OEM replacement kits holding 700 horsepower with daily driveability, clutch masters wanted to step up their clutch game and release this new 8.5 inch twin disk clutch with flywheel for the Porsche 911 turbo. This race version of the twin disk is recommended only for race use as initial pedal engagement as it requires finesse. The complete clutch weighs an astonishing 23lbs. The stock flywheel alone weighs about 40lbs! General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$6,156.00
Make a selection 20934HD00 The clutch masters fx100 system uses the power plus i pressure plate with a custom heavy-duty steel back organic friction disc. Sprung disks can be used with the OEM flywheel or aftermarket lightweight flywheels. This clutch is engineered for heavy-duty street use and is specifically designed for extended wear and additional clamping force for the enthusiast who has added an exhaust system, an intake system, up to 50hp no2 upgrade, or other non-forced induction external bolt-ons. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 TURBO/GT2 2007-09
$2,238.03
Make a selection FW934AL An excellent performance upgrade. Lightened steel flywheels are susceptible to shattering under aggressive driving conditions. Because aluminum is lighter than steel, we are able to produce aluminum flywheels utilizing stock dimensions. Aluminum flywheels are perfect for road racers looking for quicker revs. It is also a nice complement for turbocharged cars experiencing lag. General Fitment911 1994-98911 TURBO/GT2 2001-05 911 GT3 2007-11 911 TURBO/GT2 2007-09
$1,275.75
Make a selection FVD332997TQDF Helical lsd differential is suitable for Porsche with g50 gearboxes, to replace the standard open differential. A direct replacement for the standard Porsche differential. Automatic torque biasing differential enables your car to accelerate quicker and corner faster. The differential powers both drive wheels under nearly all conditions. With an ordinary open differential (standard on most cars), precious power is wasted during wheel spin under acceleration. This happens because the open differential shifts power to the wheel with less grip, along the path of least resistance. The differential, however, does just the opposite. It senses which wheel has better grip, and biases the power to that wheel. It does thi...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05
From $2,981.70
Make a selection 150PB00619 Replace worn-out original stabilizer bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. Sold individually. 2 necessary per car. Please note: this fits 911 models from 1965-73 if fitted with 19 mm original stabilizer bars. It also fits the 1975-77 930 turbo model if fitted with 19 mm original stabilizer bars.
$57.20
Make a selection 00004400050 Smooth-fitting indoor car cover featuring full-color Porsche logo. Designed for use out of the weather, as indoor protection from dust and dirt. Made from a breathable, antistatic material, features full-color Porsche logo. General FitmentACCESSORY
$509.53
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 96434705805SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)
$207.90
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,390.40
Make a selection 99704400006 Smooth-fitting indoor car cover featuring full-color Porsche logo. Designed for use out of the weather, as indoor protection from dust and dirt. Made from a breathable, antistatic material, features full-color Porsche logo. General FitmentACCESSORY
$480.01
Make a selection 99704400007 Smooth-fitting outdoor car cover featuring full-color Porsche logo. Waterrepellent fabric protects your Porsche from weather extremes such as strong sunlight. Equipped with an anti-theft protection system. Suitable for the 997 turbo. Not suitable for vehicles with aerokit. General FitmentACCESSORY
$479.16
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |